Adhesives and Grout

Rogers Ceramics Supply Ardex and Evo-Stik Products

Ardex  For  Evo-Stik Click Here  

Ardex tiling products are specially designed to meet the increasingly sophisticated challenges presented to today's specifier and fixer, whatever the application.  Backed by professional technical support and customer service, every Ardex tiling & flooring product combines unbeatable value with consistently superior quality.

Due to various reasons such as your monitor set up, colours shown are approximate and shown for a guide only - Grout colours may also vary when dry depending on type of tile installed, substrate and installation conditions.

	ARDITEX RS Size (pack): Powder 25kg, Bottles 5kg Coverage: 1.9kg of mortar/m²/mm, i.e. approx 5m² per unit at 3mm thick. The cost effective way to smooth rigid absorbent substrates, ARDITEX RS is a partially self-smoothing latex for concrete or cement/sand screeds. Can be used under a damp proof membrane.
	ARDEX-FLEX 6001 Size (pack): 11kg/22kg Coverage: 1.2kg/m²/mm of bed thickness All the advantages of Ardu-Flex 5000, but can be grouted and trafficked 1½ hours after fixing. Available in grey.   ARDEX-FLEX 6001 is classified as C2 FT (improved fast setting cementitious adhesive with additional characteristics and reduced slip) in accordance with BS EN 12004.
	ARDEX D 30 Size (pack): 10ltr Coverage: Approximately 1 litre per m² using a 3mm x 3mm toothed and notched trowel.   ARDEX D 30 is a water resistant, non-slip ready mixed wall tile adhesive for use in commercial and domestic showers, kitchens and bathrooms. Suitable for virtually all substrates and tile types, including porcelain, ARDEX D 30 does not need a primer and is easy to use with excellent application properties.   ARDEX D 30 is classified as D2 TE (improved dispersion adhesive with additional characteristics, reduced slip and extended open time) in accordance with BS EN 12004.
	ARDEX F 4  Polar white, beige or light grey   Size (pack): 2.5kg (x4)/11kg Coverage: 0.25kg/m² to 2kg/m² depending on tile size and joint width - see literature. Polar white also available in 5kg (x4) Fine grout for internal and external use, including swimming pools, etc., for joints up to 4mm wide. Both easy to apply and clean off. Walls only.
	ARDEX GK Size (pack): 11kg Coverage: 0.25kg/m² to 2kg/m² depending on tile size and joint width - see literature. Available in anthracite or grey. Rapid setting and hardening grout for internal and external use, for joint widths from 3mm upwards. Suitable for floor and wall tile joints.
	ARDEX P 82 Size (pack): 2kg/6kg Coverage: approx 30 - 60m² per 6kg unit depending on surface and application method. Solvent-free, non flammable two part primer for use on all dense impervious surfaces, including hard asphalt and rigid metal sub-floors.
	ARDEX WA Size (pack): 4kg grey or white, 2kg white Coverage: as an adhesive, 4kg units sufficient for approx 1.4 sq m of tiles or 2.2 sq m of medium or small mosaics. Coverage as a grout: 0.21kg/m² to 2.2kg/m² depending on tile size and joint width - see literature. White or grey epoxide adhesive and grout for use in wet areas, including swimming pools, easy to apply and clean off. For internal and external applications. Use where high standards of hygiene and cleanliness are required. Solvent free. Waterproof and frost resistant. For wall and floor tile joints 2-12mm wide.   ARDEX WA adhesive and grout is used for specialised applications because of its high strength and resistance. This means that ARDEX WA will withstand aqueous salt solutions and alkalis, a number of mineral and organic acids, organic solvents and solutions and in particular cleaning agents. In fact ARDEX WA is eminently suitable for abatoirs, dairies, commercial kitchens, breweries, sugar factories, silos, stables, laboratories and battery rooms.   ARDEX WA is classified as R2 T (improved reaction resin adhesive with additional characteristics and reduced slip) in accordance with BS EN 12004
	ARDEX X 7 R / ARDEX X 7 R W Rapid Setting Flexible Adhesive for Floor and Wall Tiling Size (pack): 22kg (X 7 R), 20kg (X 7 R W) Coverage: A 22kg bag of ARDEX X 7 R / X 7 R W will yield approximately 15.7 litres of mortar, equivalent to approximately 5.2m² solid 3mm bed of adhesive. Approximately 1.4kg powder/m²/mm. ARDEX X 7 R / ARDEX X 7 R W is a grey or white, rapid setting cement-based floor and wall tile adhesive which will allow grouting to commence after 2 hours at 20°C. It is specifically formulated to have enhanced properties of adhesion and flexibility ideal for fixing fully vitrified or porcelain tiles and other tiles with low porosity as well as glass and porcelain mosaics, terrazzo and brick slips without the need of an admixture. The BS EN 12004 C2 FT designation for ARDEX X 7 R / ARDEX X 7 R W classifies the adhesive as an ‘improved fast setting cementitious adhesive with additional characteristics and reduced slip’.
	ARDEX X 78 S MICROTEC® Ultra Rapid Setting Flexible Floor Tile Adhesive Unique consistency – all the benefits of a pourable without the disadvantages e.g. dripping F(F) = develops adhesion strength four times faster than the standard requires. This allows for floor tiles to be walked on and grouted after 90 minutes Unique consistency facilitates solid bedding without the need to butter the tile back Ideal for all tile types including porcelain Excellent application properties and high yield For internal and external applications Suitable for underfloor heating
	ARDEX-FLEX 5000 Size (pack): 11kg/22kg Coverage: 1.2kg/m²/mm of bed thickness Flexible adhesive for internal/external use, swimming pools etc., use with all types of tile including fully vitrified, porcelain and mosaics. Suitable for walls and floors. Available in white. Built-in admix. ARDEX-FLEX 5000 is classified as C2 S1 (improved cementitious adhesive with additional characteristics) in accordance with BS EN 12004
	ARDEX-FLEX 7001/7001 W Timber System Size (pack): 11kg (grey only), 22kg Coverage: 1.4kg/m²/mm of bed thickness Flexible rapid hardening and drying floor tile adhesive with built-in admix. Specifically designed for fixing floor tiles to wood-based sheets and boards. Available in grey or white. ARDEX-FLEX 7001/7001 W are classified as C2 FE (improved fast setting cementitious adhesive with additional characteristics and extended open time) in accordance with BS EN 12004.
	ARDITEX Size (pack): Powder 22kg, Bottles 4.8kg Coverage: 1.9kg of mortar/m²/mm, i.e. approx 5m² per unit at 3mm thick. A universal sub-floor smoothing compound, ARDITEX is used for the preparation of cement/sand and concrete screeds, quarry tiles, asphalt, granolithic or terrazzo floors and timber. ARDITEX is partially self-smoothing and can be used under a damp proof membrane.
	ARDEX C 2 Size (pack): 5kg (x4)/11kg Limestone and sandstone 11kg only Coverage: 0.25kg/m² to 2kg/m² depending on tile size and joint width - see literature. Limestone available in 11kg only Available in anthracite, beige, limestone, sandstone, grey or white. For joint widths 2mm upwards, suitable for wall and floor tiling in internal/external locations, swimming pools, etc.
	ARDEX E 90 Size (pack): 2kg/4kg Coverage: 4kg per 22kg bag of ARDEX X 7/S 16 (2kg for ARDEX S 21). Mortar admix for use with ARDEX cement-based adhesives. Gives elastic and water repellent properties plus enhanced adhesive strength if fixing to smooth or glazed surfaces.
	ARDEX-FLEX FL Size (pack): 5kg (x4)/11kg Rapid setting, flexible and water repellent grout for floor and wall tile joints from 3 - 15mm wide in internal/external locations, including swimming pools. Available in white or grey. Built-in admix.
	ARDEX K 15 Size (pack): 22kg Coverage: 1.5kg/m²/mm, i.e. approx 5m² at 3mm thick per 22kg bag. Sophisticated self-levelling sub-floor smoothing compound, can be applied to any thickness by trowel or pump. Even thick applications will be ready to receive floorcoverings within 24 hours at 20°C
	ARDEX S 16 Size (pack): 11kg/22kg Coverage: 1.4kg/m²/mm of bed thickness Grey rapid hardening and rapid drying wall and floor tile and natural stone adhesive for internal use in dry or intermittently damp locations. Can be grouted and trafficked 2-3 hours after fixing. ARDEX S 16 is classified as C2 FT (improved fast setting cementitious adhesive with additional characteristics and reduced slip) in accordance with BS EN 12004.
	ARDEX WPC Size (pack): 10kg Coverage: 6.6m² per unit to give a 0.8mm thick coating (2 coats). (Two component) - A flexible, waterproof coating for use prior to tiling in commercial shower situations. Also ideal for use on moisture sensitive backgrounds prior to tiling.
	ARDEX X 77 MICROTEC® Flexible Floor and Wall Tile Adhesive Double open time and slump resistance make fixing large format tiles easier than ever E(E) = double the current standard of 30 minutes, allowing 60 minutes before tiles need to be fixed, providing greater fixing efficiency over large areas T(T) = achieves the slip resistance standard but with a double weight tile, allowing for heavier, larger tiles to be used without slipping Ideal for all tile types including porcelain Excellent application properties and high yield Suitable for underfloor heating For internal and external applications
	ARDEX-FLEX 5001 Size (pack): 11kg/22kg Coverage: 1.1kg/m²/mm of bed thickness Flexible adhesive for internal/external use, swimming pools etc., use with all types of tile including fully vitrified, porcelain and mosaics. Suitable for walls and floors. Available in grey. Built-in admix. ARDEX-FLEX 5001 is classified as C2 TE S1(improved cementitious adhesive with additional characteristics, reduced slip and extended open time) in accordance with BS EN 12004.
	ARDEX A 45 Size (pack): 11kg bags, 5kg tubs. Coverage: 7 litres of mortar per bag. Rapid setting and drying repair mortar. Ideal for internal repair of stair treads, risers and other screed repairs. Hard enough to walk on and receive floor coverings after 1½ hours. Other applications are: forming ramps and falls, making good around fittings/pipework, filling cracks and joints, etc.
	ARDITEX NA Size (pack): Powder 22kg, Bottles 5.3kg Coverage: 1.7kg of mortar/m²/mm, i.e. approx 5.3m² per unit at 3mm thick. ARDITEX NA is a self-smoothing, protein free latex levelling compound with improved flow and excellent properties of adhesion, flexibility and water resistance. Due to its special formulation ARDITEX NA can be used under a damp proof membrane such as ARDEX DPM. It is exceptionally easy to mix and produces a very low drag on the trowel during application. In addition to these advantages, ARDITEX NA can be laid from a feather edge up to at least 12mm in a single application.
	ARDEX D 20 Size (pack): 2.5ltr/5ltr/10ltr Coverage: 10m²/10 litres for 1mm bed thickness. ARDEX D 20 is a ready mixed adhesive for fixing ceramic tiles to all internal walls in dry or intermittently wet locations, e.g. domestic showers, kitchens and bathrooms. No primer required, easy to apply with excellent slump resistance and offers up to 20 minutes open-time and 40 minutes tile adjustability. Tremendous adhesion strength and reliability.   ARDEX D 20 is classified as D1 T (normal dispersion adhesive with reduced slip) in accordance with BS EN 12004
	ARDEX E 101 Size (pack): 1kg/5kg Coverage: 1kg per 11kg bag of ARDEX grout. Grout admix for ARDEX F 4, C 2 and GK cement-based grouts and normal cement/sand grout mortars. For elastic and water repellent tile joints.
	ARDEX-FLEX FS Size (pack): 5kg (x4)/11kg Ivory and limestone 11kg only Water and dirt repellent, flexible grout. Easy to apply and clean off, suitable for use in internal/external locations, swimming pools, etc., on walls and floors. For joints up to 4mm wide. Available in brilliant white, light grey, ivory or limestone. Built-in admix
	ARDEX P 51 Size (pack): 1kg (x12), 5kg, 25kg Coverage: up to 100m² per 5kg bottle diluted 1:3 depending on porosity of substrate. Primer for porous or absorbent sub-floors, which improves the adhesion of the ARDEX sub-floor smoothing and levelling compounds, also helps prevent air bubbles/pin holes and prolongs the flow life. For use as part of the ARDEX-FLEX 7001 Timber System.
	ARDEX S 16 W Size (pack): 22kg Coverage: 1.4kg/m²/mm of bed thickness White rapid hardening and rapid drying wall and floor tile and natural stone adhesive for internal use in dry or intermittently damp locations. Ideal for fixing translucent marble, glass mosaics and other materials where a white rapid setting and drying adhesive is required. Can be grouted or trafficked 2 - 3 hours after fixing. ARDEX S 16 W is classified as C2 FT (improved fast setting cementitious adhesive with additional characteristics and reduced slip) in accordance with BS EN 12004
	ARDEX X 7 G / X 7 W Size (pack): 5kg (x4)/11kg/22kg Coverage: 1.3kg/m²/mm of bed thickness Extremely versatile tile adhesive for internal/ external use, swimming pools, etc., suitable for walls and floors. Available in grey or white. ARDEX X 7 G is classified as C1 T (normal setting cementitious adhesive with reduced slip) and ARDEX X 7 W is classified as C1 TE (normal setting cementitious adhesive with reduced slip and extended open time) in accordance with BS EN 12004
	ARDEX X 77 S MICROTEC® Ultra Rapid Setting Flexible Wall and Floor Tile Adhesive Double slump resistance stops large format wall tiles slipping F(F) = develops adhesion strength four times faster than the standard requires. This allows for wall tiles to be grouted in 60 minutes and floor tiles can be walked on and grouted after 90 minutes T(T) = achieves the slip resistance standard but with a double weight tile, allowing for heavier, larger tiles to be used without slipping Ideal for modern tiles with smooth backing surfaces Mixed adhesive has a slump-free consistency I Excellent application properties and high yield Ideal for all tile types including porcelain, fully vitrified and mosaics Suitable for under floor heating

More information can be found at www.ardex.co.uk

Find your Nearest Rogers Ceramics Showroom